Dataman Programmers USB Devices Driver Download For Windows 10

  



The USB-CANmodul1, is a small-sized and very cost-effective CAN-bus interface solution for connecting the CAN-bus to the PC via USB. CAN messages are tunneled transparently - thereby the module can support all kind of higher-layer CAN-based protocols, such as CANopen, SDS, DeviceNet or J1939.* Its fast yet low-power 32-bit CPU core with integrated message buffers ensures reliable communication even at high busload. Each received CAN message gets a precise time stamp derived from the module’s hardware timer.

Dataman

The provided PC driver allows for easy plug&play installation and supports simultaneous operation of up to 64 USB-CANmodul devices on the same PC.

An extremely attractive price-performance ratio and the compact design make this CAN USB Adapter ideal suited for CAN-bus based development, service and maintenance tasks, as well as use in high-volume serial products.

USB powered universal 48-pin chip programmer with compact dimensions and minimal weight. Dataman S6 can program without the need for a family-specific module, giving you the freedom to choose the optimal device for your design. The S6 is built to meet the demands of development labs and field engineers for universal programming. 48XP - Adds improved performance for high density FLASH parts, Windows XP support, continued device support 48UXP - Adds USB connectivity, continued device support Although the 48 and 48LV models are no longer supported the latest release of the software v4.67 is still available here.

The USB-CANmodul1 has been tested according to the EMC Directive 2014/30/EU.

* On software side for e.g. J1939 support our CANinterpreter Add On as well as J1939 protocol stack is required.

Software for device programmers

Elnec provides one common software for all device programmers. There are available regular version and OnDemand versions of software. Regular version is released normally every 3-4 weeks, OnDemand versions are released on demand - for hot new devices support and bugs fixes - often daily. For detailed description of control program for programmers look please at Software page.

Elnec software is in the form of installer, which copies control software for Elnec programmers to your hard disk, creates shortcuts in the start menu and associates project files with Elnec software, if desired.

The setup program must run with administrative rights, however Elnec software runs fine without administrative rights once it is installed.

Installation: To install Elnec software for programmers, run the PG4UWarc.EXE (or PG4UWarc-OnDemand.exe) file and follow the wizard.

Updating: Run the PG4UWarc.EXE (or PG4UWarc-OnDemand.exe) file. You do not need to uninstall the old version first. Your configuration options will not be lost.

Silent Installation: The PG4UWarc.EXE (and PG4UWarc-OnDemand.exe) installer supports command line switches for silent installation, i.e. the program gets installed without asking the user for target directory or association options. The default settings of the installer are used. The /SILENT command line switch performs a silent installation and shows a status dialog during the setup process. No questions will be asked though.

Uninstallation: In order to uninstall Elnec software for programmers, run the uninstallation program, which is accessible by a shortcut in the start menu folder of Elnec, or in the program section of the system control panel. If you also want to remove your configuration settings, you need to delete the configuration file in the application data directory of your user profile. The /SILENT command line switch can be used also here.

Dataman programmers usb devices driver download for windows 10 64-bit

Important: The software package for BeeProg3 and BeeHive304 programmers contain also updates of firmware, libraries and operating system for these programmers, which mean (roughly) next 20MB of compressed data. In intent to save download time - and also in intent to save the disk space after installation of software - we come to conclusion to provide two installation packages:

  • the first one: PG4UWarc.EXE (and PG4UWarc-OnDemand.exe) is for all Elnec programmers but doesn't include BeeProg3/BeeHive304 support.
  • the second one: PG4UWarc3.EXE (and PG4UWarc3-OnDemand.exe) is for all Elnec programmers including BeeProg3/BeeHive304 support. This package is for users of BeeProg3 and BeeHive304 programmers.
Device programmers, list of control software revisions:
Regular versions of control software, significant modifications, list of added devices, device handling improvements and fixed bugsview
OnDemand versions of control software, list of enhancements and bug fixes for other programmersview
OnDemand versions of control software, list of enhancements and bug fixes for BeeProg3/BeeHive304view

Software for device programmers (compatibility: from Windows XP to Windows 10, 32-bit and 64-bit):
programmer
(BeeProg3-core programmers)
device listdownloadversionlast changesize (B)
BeeHive304view | downloadPG4UWarc3-OnDemand.exe
(OnDemand version)
PG4UWarc3.EXE
(Regular version)
3.64o
(latest SW)
3.64
10.Feb.2021
14.Jan.2021
108,380,616
108,200,472
BeeProg3view | download
programmer
(currently produced)
device listdownloadversionlast changesize (B)
BeeHive208Sview | downloadPG4UWarc-OnDemand.exe
(OnDemand version)
PG4UWarc.EXE
(Regular version)
3.64o
(latest SW)
3.64
10.Feb.2021
14.Jan.2021
71,209,256
71,097,200
BeeHive204view | download
BeeHive204APview | download
BeeProg2view | download
BeeProg2APview | download
BeeProg2Cview | download
SmartProg2view | download
discontinued programmer
(but still supported)
device listdownloadversionlast changesize (B)
BeeHive204AP-AUview | downloadPG4UWarc-OnDemand.exe
(OnDemand version)
PG4UWarc.EXE
(Regular version)
3.64o
(latest SW)
3.64
10.Feb.2021
14.Jan.2021
71,209,256
71,097,200
BeeProg+
view | download
MEMprog2
view | download
PIKprog2
view | download
T51prog2
view | download

Notes:

Dataman Programmers Usb Devices Driver Download For Windows 10 Windows 7

  • The support of new devices implemented by OnDemand software is available for BeeProg3/BeeHive304, BeeHive208S/BeeHive204, BeeProg2/BeeProg2C/BeeProg+ and BeeHive204AP/BeeProg2AP programmers only
  • The installation file (PG4UWarc.EXE and PG4UWarc-OnDemand.exe) may be keeped to reinstall SW in the future.


USB

Dataman Programmers Usb Devices Driver Download For Windows 10 64-bit

PC requirements

Minimal PC requirements
Operating systemCPURAMdisk space
( free )
USB 2.0
high speed
LPT LAN
2x BeeHive304Windows XPC2Quad2 GB500 MB1 Gb
2x BeeHive204APWindows XPC2D1 GB500 MB
2x BeeHive204Windows XPC2D1 GB500 MB
BeeHive304Windows XPC2D2 GB500 MB1 Gb
BeeHive204APWindows XPC2D1 GB500 MB
BeeHive204Windows XPC2D1 GB500 MB
BeeProg3Windows XPC2D1 GB500 MB100 Mb
BeeProg2Windows XPC2D1 GB500 MB
BeeProg2CWindows XPC2D1 GB500 MB
BeeProg2APWindows XPC2D1 GB500 MB
SmartProg2Windows XPC2D1 GB500 MB
Notes:
  • For best performance we recommend 1024 x 768 or higher screen resolution.
  • The 'Minimal PC requirements' mean, the device programmer and SW will run at these conditions, but not with fully enjoyable experience

Optimal PC requirements
Operating system CPU RAMdisk space
(free)
2x USB 2.0
high speed
USB 2.0
high speed
LAN
2x BeeHive304
Windows 7Core i5 *14 GB *22 GB *21 Gb
2x BeeHive204APWindows 7Core i5 *14 GB *22 GB *2
2x BeeHive204Windows 7Core i5 *14 GB *22 GB *2
BeeHive304Windows 7Core i3 *12 GB *22 GB *21 Gb
BeeHive204APWindows 7Core i3 *12 GB *21 GB *2
BeeHive204Windows 7Core i3 *12 GB *21 GB *2
BeeProg3Windows 7Core i3 *12 GB *21 GB *21 Gb
BeeProg2Windows 7Core i3 *12 GB *21 GB *2
BeeProg2CWindows 7Core i3 *12 GB *21 GB *2
BeeProg2APWindows 7Core i3 *12 GB *21 GB *2
SmartProg2Windows 7Core i3 *12 GB *21 GB *2
Driver*1 - or better
*2 - or more
Notes:
  • These PC requirements are valid for 3.38 version of control program for programmers (issued 01.Feb.2018) and above.
  • If two programmers are to be connected to a single PC, then we strongly recommend to connect each programmer to separate USB 2.0 High speed controller (USB EHCI). For more information see User manual for the programmer, the 'Hardware setup' chapter.
  • Free disk space requirements depends also on used IC device size and number of attached programming sites. For large devices the required free space on disk will be approximately 1000MB+ 2x Device sizexnumber of programming sites attached to this PC.
  • Very easy indication, if your PC in hardware/software configuration is good enough for the current software version and current situation with PG4UW/PG4UWMC, is to run Windows task manager (Ctrl+Alt+Del) and see the performance folder. It has to be max. 80% of CPU usage at full run of programming system.
  • We still recommend Windows 7 because of unexpected restarts after automatic updates of the Windows 10. If you are fine with this, you can use Windows 10.

Notes to the BeeHive208S programmers:
  • for work with the actual version of SW the BeeHive208S programmers must have installed 2GB RAM or above.
  • except the above RAM size increase, the PC inside of the all BeeHive208S programmers is still above the Minimal PC requirements for actual version of the software.


Manuals and other documents

Operating manuals updates
nameformatlanguagelast changesize (B)
User manual for BeeHive304 and BeeProg3 programmers
PDFenglishMar. 01, 20193,25 MB
User manual for BeeHive204AP and BeeProg2AP multiprogramming system
PDFenglishDec. 11, 20195,66 MB
User manual for BeeHive208S Stand-Alone multiprogramming system
(Windows Embedded 8.1 Industry Pro)
PDFenglishSep. 04, 20174,34 MB
User manual for BeeHive208S Stand-Alone multiprogramming system
(Windows XP Embedded)
PDFenglishSep. 04, 20173,15 MB
User manual for BeeHive8S Stand-Alone multiprogramming system
PDFenglishMar. 18, 20091,10 MB
Latest version of User manual for BeeHive204, BeeProg2, BeeProg2C and SmartProg2 device programmers
PDFenglishMar. 02, 20214,16 MB
Previous version of user manual that contain also discontinued Elnec device programmers
(Contain: BeeHive204, BeeProg2, BeeProg2C, BeeProg+, SmartProg2, MEMprog2, SEEprog)
PDFenglishJune. 26, 20125,29 MB
Previous version of user manual that contain also discontinued Elnec device programmers
(Contain: BeeHive204, BeeHive4+, BeeProg2, BeeProg+, SmartProg2, MEMprog2, T51prog2, PIKprog2, MEMprogL, SEEprog)
PDFenglishApr. 13, 20115,43 MB
Previous version of user manual that contain also discontinued Elnec device programmers
(Contain: JetProg, BeeProg, LabProg+, SmartProg2, SmartProg, PREPROM-02aLV, MEMprog, MEMprogL, T51prog, 51&AVRprog, PIKprog+, PIKprog, SEEprog)
PDFenglishAug. 17, 20053,71 MB
User manual for BeeHive4 multiprogramming system
PDFenglishSep. 16, 20051,53 MB
User manual for JetProg - multiprogramming system
PDFenglishFeb. 25, 2003405,88 KB
User manual for Elnec EPROM simulators
PDFenglishAug. 01, 20031,06 MB
User manual for EREPROM-01A eraser
PDFenglishSep. 22, 200347,24 KB

You need to have PDF files. You can use Adobe Acrobat Reader.
But better might be Sumatra PDF - faster and smaller. Get Sumatra PDF


Unsupported products


Last version of software for no longer supported products:
productOSdownloadversionlast changesize (B)
BeeHive8S (device list)pg4uwarc356.exe3.56Mar, 01, 202061,7 MB
BeeHive4+ (device list)pg4uwarc356.exe3.56Mar, 01, 202061,7 MB
MEMprogL (device list)pg4uwarc356.exe3.56Mar, 01, 202061,7 MB
SEEprog (device list)pg4uwarc356.exe3.56Mar, 01, 202061,7 MB
MemProg (device list)pg4uwarc347.exe3.47Jan, 31, 201959,0 MB
BeeHive4 (device list)pg4uwarc332.exe3.32May, 11, 201754,6 MB
BeeProg (device list)pg4uwarc332.exe3.32May, 11, 201754,6 MB
JetProg (device list)pg4uwarc328.exe3.28Dec. 08, 201654,8 MB
SmartProg (device list)pg4uwarc325.exe3.25Jun. 23, 201653,7 MB
PikProg+ (device list)pg4uwarc325.exe3.25Jun. 23, 201653,7 MB
T51prog+ (device list)pg4uwarc325.exe3.25Jun. 23, 201653,7 MB
LabProg+ (device list)pg4uwarc321.exe3.21Jan. 28, 201653,3 MB
PREPROM-02aLV (device list)pg4uwarc315.exe3.15Jun. 30, 201551,9 MB
51&AVRprog (device list)pg4uwarc299.exe2.99Jun. 20, 201342,8 MB
PIKprog (device list)pg4uwarc299.exe2.99Jun. 20, 201342,8 MB
LabProg-48LV (device list)pg4uwarc274.exe2.74Dec. 16, 201031,60 MB
PREPROM-02 (device list)pg4uwarc251.exe2.51Aug. 14, 200824,07 MB
PREPROM-03 EPROM/Flash gang programmer (device list) PG023ARC.EXE3.98cAug. 16, 1999295,28 KB
PREPROM-01 EPROM programmerPGO1.ZIP-12/1999138,05 KB
SIM2051 emulator/programmer AT89C2051S2051ARC.EXE3.11Mar. 21, 2000 197,57 KB
T-EMU52 emulatorTEMU52AR.EXE1.44Jan. 03, 2002245,26 KB
SIMEPROM-01B/-02/-02aLV
simulators
simwarc.exe1.1822.May.20071,41 MB
SIMEPROM-01B/-02/-02aLV
simulators
sim12arc.exe4.1728.May.2002256,11 KB
SIMEPROM-01/-01A EPROM simulatorsSIM12ARC.EXE-6/2001256,11 KB
Devices
Software for device programmers (DOS)
programmerdownloadversionlast changesize (B)
JetProg, LabProg+, LabProg-48LV, SmartProg, T51prog, 51&AVprog, PIKprog+, PIKprog, SEEprog, PREPROM-02PG4Uarc.EXE4.93a26.Jun.20032,46 MB

Dataman Programmers Usb Devices Driver Download For Windows 10 Offline

Note:

Dataman Programmers Usb Devices Driver Download For Windows 10 Pro

  • DOS version of SW for programmers has been discontinued since 7/2003. The software will not work with programmers, manufactured after this date. We provide none support and none consultations regarding DOS version of SW for programmers.
  • The version of SW can be used for MS-DOS OS, as well for WIN 3.xx, WIN95, WIN98/Me.